07
2026.08

CNC-Blechlaserschneidmaschine: So konfigurieren Sie die richtige Anlage

18:37

Speccing a CNC sheet metal laser cutting machine means matching four things to your actual part mix: sheet format, laser power tier, platform type, and material thickness range. Get the format and platform right first. Power tiers can be adjusted at quotation; a table that cannot hold your sheets cannot be fixed later.

Blech-Laserschneidmaschine

Beginnen Sie mit dem Teilespektrum, nicht mit der Leistungsangabe

Most vendor category pages open with a maximum: highest kilowatt rating, thickest plate cut. Those numbers describe the ceiling of what a machine can do once, not what it will do eight hours a day on your job floor.
Die Informationen, die den Kauf tatsächlich eingrenzen, liegen in Ihren eigenen Produktionsdaten. Bevor Sie sich auch nur eine einzige Modellseite ansehen, sollten Sie die Fertigungsaufträge der letzten sechs bis zwölf Monate heranziehen und Folgendes ermitteln:

  1. Die Verteilung der eingekauften Rohblechformate nach Volumen – nicht das größte Format, das Sie je gekauft haben
  2. Material types and the thickness band that covers roughly 80% of parts by count
  3. Material types and thickness band for the remaining 20%, listed separately
  4. Average batch size per job, and how many distinct jobs run per shift
  5. Whether nesting is done per-order or pooled across orders
  6. Your current bottleneck: is it cutting time, or is it loading, unloading and sorting?

That last item decides more than the laser source does. A shop where the beam is idle 40% of the shift while an operator clears a table is not short of power. It is short of platform.

So lesen Sie die Modellnummern

HWlEiC‘s sheet cutting models use a four-digit format code: A3015, A4020, F6015, F6025. Across the sheet metal laser sector this code convention refers to nominal working area, first pair as length and second pair as width, each in units of 100 mm. On that reading, a 3015 designation points at a 3000 × 1500 mm table and a 6025 designation at 6000 × 2500 mm.
Treat that as a reading aid, not a datasheet. HWlEiC does not publish table dimensions, cutting accuracy or maximum thickness on the public A Series and F Series pages, so the exact working envelope, clamping allowance and usable travel for any given model need to be confirmed in writing before you design material flow around them. Ask for the drawing, not the code.

So lesen Sie die Modellnummern

HWlEiC‘s sheet cutting models use a four-digit format code: A3015, A4020, F6015, F6025. Across the sheet metal laser sector this code convention refers to nominal working area, first pair as length and second pair as width, each in units of 100 mm. On that reading, a 3015 designation points at a 3000 × 1500 mm table and a 6025 designation at 6000 × 2500 mm.
Treat that as a reading aid, not a datasheet. HWlEiC does not publish table dimensions, cutting accuracy or maximum thickness on the public A Series and F Series pages, so the exact working envelope, clamping allowance and usable travel for any given model need to be confirmed in writing before you design material flow around them. Ask for the drawing, not the code.

Modell Positionierung der Baureihen Nominal Format Code Plattformtyp
A3015 Einfache Einzelplattform 3015 Einzelplattform
A4015 Einfache Einzelplattform 4015 Einzelplattform
A4020 Einfache Einzelplattform 4020 Einzelplattform
A6025 Einfache Einzelplattform 6025 Einzelplattform
F3015 Classic Single Plane 3015 Einzelplattform
F4020 Classic Single Plane 4020 Einzelplattform
F6015 Classic Single Plane 6015 Einzelplattform
F6025 Classic Single Plane 6025 Einzelplattform

Das Serie wird im Katalog als einfache Einzeltischmaschine beschrieben, die als praktische industrielle Lösung für das Schneiden von Blechen positioniert ist.

Das F-Serie is described as a classic single plane machine, with metal sheet cutting, high-precision processing and stable industrial production listed as its characteristics.
Wenn man das ehrlich betrachtet: Der Katalog unterscheidet die beiden Baureihen eher nach dem vorgesehenen Einsatzbereich als anhand veröffentlichter Kennzahlen. Die A-Serie liest sich wie die Einstiegskonfiguration für Betriebe mit fest vorgegebenem Format und Genauigkeitsanforderungen im Rahmen gewöhnlicher Fertigungstoleranzen. Die F-Serie versteht sich als die Stufe darüber, bei der Präzision und Dauerbetrieb hervorgehoben werden. Welche dieser Beschreibungen zu Ihren Bauteilen passt, klären Sie am besten im Gespräch mit einem Ingenieur – anhand Ihrer Fertigungszeichnungen.

The format spread matters more than the series letter for most buyers. Four of the eight models above are 4020 or larger, and two reach the 6025 code — that range exists because sheet stock purchasing varies by region and by material supplier, not because bigger is better. Buying a 6025 table to cut 1500 mm stock leaves you paying for gantry mass, floor space and enclosure volume that never carries a part.

Metall Blatt Laser Schneiden Maschine

Einzeltisch oder Wechseltisch?

Jedes Modell in diesem Leitfaden ist für eine einzige Plattform ausgelegt. Das ist eine echte Einschränkung und sollte klar benannt werden, statt sie als Fußnote abzutun.
Bei einer Einzelplattform-Maschine erfolgen das Be- und Entladen auf demselben Tisch, über dem der Strahl arbeitet. Während dieser Zeit steht die Maschine still. Bei einer Wechseltisch-Maschine – die E-Serie von HWlEiC ist die Wechseltisch-Konfiguration im Katalog für die Blechbearbeitung – wird auf einem Tisch geschnitten, während der andere abgeräumt und neu beladen wird, und die Tische werden getauscht.

Der Test ist unkompliziert. Schätzen Sie anhand Ihrer eigenen Aufzeichnungen die Schneidzeit pro Blech und die Handlingzeit pro Blech ab; dann gilt:

  • If cut time per sheet runs long relative to handling, single platform gives up little. Thick material, dense nests and long unbroken cut paths all push you here.
  • If handling time approaches or exceeds cut time, the beam is idle for a large share of the shift and an exchange table converts that directly into output. Thin material, sparse nests and small parts that need sorting all push you here.
  • If your part mix is one large sheet a shift, or if your shop runs a single operator who handles cutting alongside other duties, the second table earns nothing.

Der Platzbedarf ist das Gegengewicht. Ein Wechseltisch beansprucht ungefähr die Stellfläche von zwei Tischen plus Freiraum für den Tischwechsel und bringt eine Mechanik mit sich, die gewartet werden muss. Betriebe, die bei sich einen tatsächlichen Engpass beim Handling gemessen haben, bereuen diese Entscheidung jedoch selten.

Shops that bought it because it appeared on the comparison chart usually run it as a single-platform machine with an expensive second table parked underneath.

Austausch Plattform Faser laser schneiden Maschine

 

Ein sechsstufiger Workflow zur Spezifikation

Work through these in order. Each step should end with a number or a decision you can hand to a supplier.
Schritt 1 — Das Blechformat festlegen. Take the 90th percentile of your raw stock sizes, add your clamping and edge allowance, and round up to the nearest available format code. This produces one or two candidate codes and eliminates the rest of the catalogue. Verification: you can name the model codes still in contention.
Schritt 2 — Den Dickenbereich eingrenzen. Notieren Sie den Dickenbereich, der 80 % der Teile abdeckt, und erfassen Sie den Bereich für Ausreißer separat. Legen Sie die Maschine nicht auf Ausreißer aus, es sei denn, sie machen mehr als rund ein Fünftel Ihres Volumens aus; das Auslagern dicker Ausreißerteile ist oft günstiger als der Kauf von Laserleistung, die Sie nur einmal pro Woche nutzen. Verifikation: Sie haben zwei Bereiche notiert, jeweils mit einer Prozentangabe.

Step 3 — Request the power recommendation.Do not assume it. Give the supplier the two thickness ranges, the materials by name, and your required edge quality and cut speed target. Ask for a recommended power tier against that brief. Verification: you have a written power recommendation tied to your stated materials.
Schritt 4 – Führen Sie den Plattformtest durch. Compare measured handling time per sheet against estimated cut time per sheet from Step 2. Verification: you have chosen single platform or exchange platform, and can state the ratio that drove it.

Step 5 — Confirm the published envelope in writing. Request working area drawing, positioning accuracy, repeatability, machine footprint including service clearance, and power supply requirement. Where a figure is not on the public page, it must appear on the quotation. Verification: nothing on your spec sheet reads “assumed.”
Step 6 — Specify what happens after installation. Umfang der Inbetriebnahme, Schulungstage für Bediener, Ersatzteilliste für das erste Jahr, zugesagte Reaktionszeit und Verfügbarkeit von Verbrauchsmaterialien in Ihrer Region. Überprüfung: Für jeden dieser Punkte gibt es ein konkret benanntes Ergebnis, nicht nur eine Zusicherung.

Where Buyers Get This Wrong

Speccing to the outlier part. The most common error is sizing the whole machine around the thickest or largest part in the catalogue, which is frequently a legacy job or a one-off. The cost of that decision compounds: larger table, higher power, bigger chiller, more floor, more extraction, higher running cost per part on the 80% of work that never needed any of it.
Reading maximum thickness as production thickness. A stated maximum cut thickness is typically a capability figure, achieved at low feed rate and with a particular assist gas and edge quality. Production thickness — the band a machine runs economically all shift — sits below it. When a supplier quotes a maximum, ask separately what thickness they would run continuously for your quality requirement.
Overlooking assist gas economics. Der Gasverbrauch über die Lebensdauer einer Maschine kann dem Unterschied im Anschaffungspreis zweier infrage kommender Modelle nahekommen – und er schwankt je nach Material, Blechdicke und geforderter Schnittkantenqualität erheblich. Die Edelstahlbearbeitung mit hohem Stickstoffverbrauch weist ein völlig anderes Betriebskostenprofil auf als mit Sauerstoff geschnittener Kohlenstoffstahl. Einkäufer, die lediglich Maschinenangebote vergleichen, vergleichen eine unvollständige Zahl.
Ein erwähnenswerter Sonderfall: shops running highly reflective materials such as copper and brass. Fiber sources handle reflective metals far better than earlier laser types did, but the specification conversation changes — cutting head protection, permitted thickness on reflective stock, and any warranty conditions attached to it should be raised explicitly and answered in writing before the order. Do not assume a general steel-cutting spec transfers.

Zertifizierung und was sie Ihnen nicht sagt

HWlEiC Laser verfügt über eine Zertifizierung des Qualitätsmanagementsystems nach ISO 9001:2015 und weist öffentlich die CE- und RoHS-Konformität aus. Diese drei Nachweise beantworten unterschiedliche Fragen, weshalb es sinnvoll ist, sie getrennt zu betrachten.
ISO 9001:2015 ist eine von der Internationalen Organisation für Normung herausgegebene Norm für Qualitätsmanagementsysteme. Sie bescheinigt, dass ein Hersteller dokumentierte, auditierte Prozesse für Entwicklung, Produktion und Korrekturmaßnahmen anwendet. Sie bescheinigt nicht, dass eine einzelne Maschine bestimmte Leistungswerte erzielt – ein Unterschied, den Einkäufer regelmäßig verwischen.
Die CE-Konformität betrifft die Einhaltung der geltenden europäischen Gesundheits-, Sicherheits- und Umweltanforderungen, was für den Import in den EWR und oft auch für Versicherungen sowie die Standortabnahme an anderen Orten von Bedeutung ist. RoHS regelt die Beschränkung bestimmter gefährlicher Stoffe in den Geräten.

What none of them tells you is cut quality, uptime or service responsiveness. Certification is a floor to check for, then move past. The questions that predict satisfaction two years in are about spare parts lead time, local engineer availability and whether the supplier will run your parts as a sample before the order.

Where This Leaves You

Compared with the vendor category pages that dominate this search — which publish power and thickness ceilings and leave the matching exercise to the buyer — the sequence above is deliberately boring: format, thickness, power, platform, envelope, aftersales, in that order. It produces a shortlist of two or three model codes rather than a catalogue.
Two things this guide has not covered and you may need next: nesting software and its effect on material yield, which often moves cost per part more than the machine choice does; and automation add-ons such as tower storage or automatic loading, which change the platform calculation entirely and are worth evaluating before, not after, the machine decision is locked.
If your part mix includes tube or profile alongside sheet, the specification path diverges early — combination sheet-and-tube configurations exist as a separate product family and should be scoped as one decision rather than two.

FAQ

F: Worin besteht der Unterschied zwischen den Blech-Laserschneidmaschinen der A-Serie und der F-Serie?

A: Bei beiden handelt es sich um Einzelplattform-Blechschneidmaschinen. HWlEiC positioniert die A-Serie als grundlegende Einzelebenen-Maschine für das praktische industrielle Blechschneiden und hebt die F-Serie als klassische Einzelebenen-Maschine für hochpräzise Bearbeitung und eine stabile industrielle Fertigung hervor. Detaillierte Leistungs- und Genauigkeitsspezifikationen sind auf den öffentlichen Produktseiten nicht veröffentlicht und sollten für die konkreten Modelle angefordert werden, die Sie vergleichen.
Q: What sheet size does a 3015 or 6025 model refer to?

A: The four-digit code follows the sector convention of nominal working area in units of 100 mm — 3015 pointing at approximately 3000 × 1500 mm, 6025 at approximately 6000 × 2500 mm. Confirm the exact usable working area and clamping allowance with the supplier before planning material flow, as HWlEiC does not publish table dimensions publicly.
Q: Do I need an exchange platform machine?

A: Compare handling time per sheet against cut time per sheet in your current production. If handling time approaches or exceeds cut time, an exchange table converts idle beam time into output. If cut times are long relative to handling, a single-platform machine such as the A Series or F Series gives up very little. HWlEiC’s E Series is the exchange table configuration in the sheet cutting catalogue.
Q: How much does a CNC sheet metal laser cutting machine cost?

A: Pricing is not published and requires a customized evaluation. Cost is driven by laser power, working area, machine configuration, automation requirements and material application. Sending your sheet format, material types and thickness distribution with the enquiry will produce a specific quotation.
Q: What certifications should I check for?

A: HWlEiC Laser verfügt über eine Zertifizierung seines Qualitätsmanagementsystems nach ISO 9001:2015 und weist die Einhaltung von CE und RoHS öffentlich aus. Zertifikatsnummern und ausstellende Stellen werden nicht öffentlich genannt; fordern Sie daher während der Evaluierung Kopien an. Beachten Sie, dass ISO 9001:2015 die Qualitätsprozesse des Herstellers zertifiziert, nicht die Leistung einer einzelnen Maschine.
F: Können diese Maschinen Kupfer und Messing schneiden?

A: Reflective materials require an explicit conversation about cutting head protection, permitted thickness on reflective stock and any warranty conditions attached. Raise it before the order and get the answer in writing rather than assuming a general steel-cutting specification applies.

 

Holen Sie sich ein Angebot

    Wir werden Antwort Sie innerhalb 24 Stunden. Wenn für dringenden Fall, fügen Sie bitte WhatsApp/WeChat: +86 15589913375. Oder rufen Sie +86 15589913375 direkt.

    *Wir respektieren die Vertraulichkeit und alle Informationen geschützt sind.

    Wir verwenden Ihre Informationen nur zur Beantwortung Ihrer Anfrage und sendet niemals unaufgefordert E-Mails oder Werbe-Nachrichten.

    Produkte

    Tipps: Füllen Sie die Nachricht, bevor Sie erhalten das Produkt-parameter-Handbuch

    POWER TOOLS

    Ultimative Dynamik und Effizienz

    Haltbarkeit und Zuverlässigkeit

    Präzision und Genauigkeit aktualisiert

    Intelligente & Benutzerfreundlichkeit

    Sicherheit & gesund

    Flexible automation

      • *Name

      • *E-mail

      • *Telefon oder WhatsApp

      • *Land

      • Stadt

      • Unternehmen

      • *Schneidstoff

      • Maschine Typ

      • *Nachricht

      Submit-button mit der Bestätigung: “ich Danke Ihnen! Unser team wird erreichen Sie in Kürze.